86-574-86369916 •

ADP Withdrawal Sleeve AH308-AHX322

ADP Withdrawal Sleeve AH308-AHX322 Admin Edit

Min. Order: 10 Piece/Pieces
Payment Terms: L/C, T/T
Place of Origin: Zhejiang, China (Mainland)
Means of Transport: Ocean, Air
Production Capacity: 90 tons of seamless...
Packing: Plastic-bag/ Box ...
Delivery Date: 30-45days
Brand Name: ADP Certificate: ISO9001
Export Area: Global

Withdrawal Sleeve AH308-AHX322

Withdrawal Sleeve AH308-AHX322

 

DesignationGd1dG1B1B2
AH308M45×1.5354062932
AH309M50×1.5404563134
AHX310M55×2455073538
AHX311M60×2505573740
AHX312M65×2556084043
AH313M75×2606584245
AH314M80×2657084347
AH315M85×2707584549
AH316M90×2758084852
AHX317M95×2808595256
AHX318M100×2859095357
AHX319M105×29095105761
AHX320M110×295100105963
AHX321M115×2100105126266
AHX322M120×2105110126367



ADP withdrawal sleeves can be used to mount bearings with a tapered bore on cylindrical seats of stepped shafts. The sleeve is pressed into the bore of the bearing that abuts a shaft shoulder or similar fixedcomponent. The sleeve is located on the shaft by a nut or an end plate. Lock nuts or endplates are not supplied with the extraction sleeves. KM or HM lock nuts and respective locking washers are suitable but must be ordered separately. Further information will be found in the section "Lock nuts with locking washer or clip".To secure the bearing to the shaft, press the extraction sleeve into the bearing bore. To do this, particularly where larger bearings are concerned, considerable force is required to overcome the friction between the mating surfaces of the bearing and sleeve and of the sleeve and shaft. Mounting and dismounting of bearings on extraction sleeves can be facilitated considerably by using a hydraulic nut .

Basic design
ADP extraction sleeves are slotted and have an external taper of 1:12 except for those in the A(O)H 240 and A(O)H 241 series which have an external taper of 1:30 and are intended for use with wide bearings in the 40 and 41 Dimension Series.


The nuts required for dismounting the extraction sleeve are not supplied with the sleeve and must be ordered separately. Appropriate sizes are listed in the product table. Appropriate hydraulic nuts for dismounting are listed there as well.

Design for hydraulic mounting
To enable the hydraulic mounting to be used for mounting and dismounting, ADP extraction sleeves with bore diameters of 200 mm and above are produced as standard with oil supply ducts and distributor grooves. 



These AOH sleeves have two oil supply ducts at the threaded side as well as oil distributor grooves in the circumferential and axial directions, both in the outside surface and the sleeve bore. If oil is injected through these ducts and grooves, an oil fil is formed between the mating surfaces of the bearing and sleeve and between the shaft and sleeve, and the force required to mount the bearing is considerably reduced. Details of the thread for attaching the oil supply lead to the ducts as well as of appropriate hydraulic nuts can be found in the product table.

Materials
The materials using in ADP extraction sleeves are carbon steel with a tensile strength at least 430N /mm2.

Dimensions
The dimensions of ADP extraction sleeves are in accordance with ISO 2982-1:1995.

Tolerances
The bore diameter of ADP extraction sleeves is to tolerance JS9, the width to h13.

Thread
ADP extraction sleeves up to size 38 have metric threads with 6g tolerances according to ISO 965-3:1998. Larger extraction sleeves have metric trapezoidal threads with 7e tolerance according to ISO 2903:1993.If standard nuts are not used, the threads of nuts for extraction sleeves up to size 38 should correspond to tolerance 5H according to ISO 965-3:1998. The threads of nuts for larger extraction sleeves should correspond to tolerance 7H according to ISO 2903:1993.

Shaft tolerances
As extraction sleeves adapt themselves to the shaft diameter, wider diameter tolerances can be permitted than for the seating of a bearing with a cylindrical bore. However, the form tolerances must be kept within narrow limits as the accuracy of form directly affects the running accuracy of the bearing. Generally, shafts should be machined to an h9 tolerance but the cylindricity should be to IT5/2 according to ISO 1101:2004.



PRODUCT DETAIL ADP Withdrawal Sleeve AH208-AH222

ADP Withdrawal Sleeve AH208-AH222

AH2 Series
PRODUCT DETAIL ADP Withdrawal Sleeve AHX3120-AHX3188

ADP Withdrawal Sleeve AHX3120-AHX3188

AH31 Series
PRODUCT DETAIL ADP Withdrawal Sleeve AHX3024-AHX3092

ADP Withdrawal Sleeve AHX3024-AHX3092

AH30 Series
PRODUCT DETAIL ADP Withdrawal Sleeve for bearings

ADP Withdrawal Sleeve for bearings

AH241 Series
PRODUCT DETAIL ADP Withdrawal Sleeve AH2308-AH2356

ADP Withdrawal Sleeve AH2308-AH2356

AH23 Series
PRODUCT DETAIL ADP Withdrawal Sleeve AHX3218-AH3272

ADP Withdrawal Sleeve AHX3218-AH3272

AH32 Series
PRODUCT DETAIL ADP Withdrawal Sleeve AH2236-AH2264

ADP Withdrawal Sleeve AH2236-AH2264

AH22 Series

Category: others