86-574-86369916 •

ADP Withdrawal Sleeve AHX3024-AHX3092

ADP Withdrawal Sleeve AHX3024-AHX3092 Admin Edit

Min. Order: 10 Piece/Pieces
Payment Terms: L/C, T/T
Place of Origin: Zhejiang, China (Mainland)
Means of Transport: Ocean, Air
Production Capacity: 90 tons of seamless...
Packing: Plastic-bag/ Box ...
Delivery Date: 30-45days
Brand Name: ADP Certificate: ISO9001
Export Area: Global

Withdrawal Sleeve AHX3024-AHX3092

Withdrawal Sleeve AHX3024-AHX3092

 

DesignationGd1dG1B1B2
AHX3024M130×2115120136064
AHX3026M140×2125130146771
AHX3028M150×2135140146873
AHX3030M160×3145150157277
AH3032M170×3150160167782
AH3034M180×3160170178590
AH3036M190×3170180179298
AH3038Tr205×41801901896102
AH3040Tr215×419020019102108
AH3044Tr235×420022020111117
AH3048Tr260×422024021116123
AH3052Tr280×424026023128135
AH3056Tr300×426028024131139
AH3060Tr320×528030026145153
AH3064Tr345×530032027149157
AH3068Tr365×532034028162171
AH3072Tr385×534036030167176
AH3076Tr410×536038031170180
AH3080Tr430×538040033183193
AH3084Tr450×5    40042034186196
AHX3088Tr470×542044035194205
AHX3092Tr490×544046037202213


ADP withdrawal sleeves can be used to mount bearings with a tapered bore on cylindrical seats of stepped shafts. The sleeve is pressed into the bore of the bearing that abuts a shaft shoulder or similar fixedcomponent. The sleeve is located on the shaft by a nut or an end plate. Lock nuts or endplates are not supplied with the extraction sleeves. KM or HM lock nuts and respective locking washers are suitable but must be ordered separately. Further information will be found in the section "Lock nuts with locking washer or clip".To secure the bearing to the shaft, press the extraction sleeve into the bearing bore. To do this, particularly where larger bearings are concerned, considerable force is required to overcome the friction between the mating surfaces of the bearing and sleeve and of the sleeve and shaft. Mounting and dismounting of bearings on extraction sleeves can be facilitated considerably by using a hydraulic nut .

Basic design
ADP extraction sleeves are slotted and have an external taper of 1:12 except for those in the A(O)H 240 and A(O)H 241 series which have an external taper of 1:30 and are intended for use with wide bearings in the 40 and 41 Dimension Series.


The nuts required for dismounting the extraction sleeve are not supplied with the sleeve and must be ordered separately. Appropriate sizes are listed in the product table. Appropriate hydraulic nuts for dismounting are listed there as well.

Design for hydraulic mounting
To enable the hydraulic mounting to be used for mounting and dismounting, ADP extraction sleeves with bore diameters of 200 mm and above are produced as standard with oil supply ducts and distributor grooves. 



These AOH sleeves have two oil supply ducts at the threaded side as well as oil distributor grooves in the circumferential and axial directions, both in the outside surface and the sleeve bore. If oil is injected through these ducts and grooves, an oil fil is formed between the mating surfaces of the bearing and sleeve and between the shaft and sleeve, and the force required to mount the bearing is considerably reduced. Details of the thread for attaching the oil supply lead to the ducts as well as of appropriate hydraulic nuts can be found in the product table.

Materials
The materials using in ADP extraction sleeves are carbon steel with a tensile strength at least 430N /mm2.

Dimensions
The dimensions of ADP extraction sleeves are in accordance with ISO 2982-1:1995.

Tolerances
The bore diameter of ADP extraction sleeves is to tolerance JS9, the width to h13.

Thread
ADP extraction sleeves up to size 38 have metric threads with 6g tolerances according to ISO 965-3:1998. Larger extraction sleeves have metric trapezoidal threads with 7e tolerance according to ISO 2903:1993.If standard nuts are not used, the threads of nuts for extraction sleeves up to size 38 should correspond to tolerance 5H according to ISO 965-3:1998. The threads of nuts for larger extraction sleeves should correspond to tolerance 7H according to ISO 2903:1993.

Shaft tolerances
As extraction sleeves adapt themselves to the shaft diameter, wider diameter tolerances can be permitted than for the seating of a bearing with a cylindrical bore. However, the form tolerances must be kept within narrow limits as the accuracy of form directly affects the running accuracy of the bearing. Generally, shafts should be machined to an h9 tolerance but the cylindricity should be to IT5/2 according to ISO 1101:2004.



PRODUCT DETAIL ADP Withdrawal Sleeve for bearings

ADP Withdrawal Sleeve for bearings

AH241 Series
PRODUCT DETAIL ADP Withdrawal Sleeve AH2308-AH2356

ADP Withdrawal Sleeve AH2308-AH2356

AH23 Series
PRODUCT DETAIL ADP Withdrawal Sleeve AH308-AHX322

ADP Withdrawal Sleeve AH308-AHX322

AH3 Series
PRODUCT DETAIL ADP Withdrawal Sleeve AHX3218-AH3272

ADP Withdrawal Sleeve AHX3218-AH3272

AH32 Series
PRODUCT DETAIL ADP Withdrawal Sleeve AH2236-AH2264

ADP Withdrawal Sleeve AH2236-AH2264

AH22 Series
PRODUCT DETAIL ADP Withdrawal Sleeve AH208-AH222

ADP Withdrawal Sleeve AH208-AH222

AH2 Series
PRODUCT DETAIL ADP Withdrawal Sleeve AHX3120-AHX3188

ADP Withdrawal Sleeve AHX3120-AHX3188

AH31 Series

Category: others