ADP Withdrawal Sleeve AHX3218-AH3272

Model: AH32 Series
Place of Origin: Zhejiang,China (Mainland)
Brand Name: ADP
Certificate: ISO9001
Export Area: Global

inquiry

basketAdd to Basket  Edit

Share |

Product Description

Payment & Shipping Terms Supply Capacity
Payment Terms:L/C, T/TProduction Capacity:90 tons of seamless...
Min. Order:10 Piece/PiecesPacking:Plastic-bag/ Box ...
Means of Transport:Ocean, AirDelivery Date:30-45days

Withdrawal Sleeve AHX3218-AH3272

Withdrawal Sleeve AHX3218-AH3272

 

DesignationGd1dG1B1B2
AHX3218M100×28590106367
AH3219M105×29095116771
AHX3220M110×295100117377
AH3221M115×2100105117882
AHX3222M125×2105110118286
AHX3224M135×2115120139094
AHX3226M145×21251301598102
AHX3228M155×313514015104109
AHX3230M165×314515017114119
AH3232M180×315016020124130
AH3234M190×316017024134140
AH3236M200×317018024140146
AH3238Tr210×418019025145152
AH3240Tr220×419020025153160
AH3260Tr330×528030034228236
AH3264Tr350×530032036246254
AH3268Tr370×532034038264273
AH3272Tr400×534036040274283





ADP withdrawal sleeves can be used to mount bearings with a tapered bore on cylindrical seats of stepped shafts. The sleeve is pressed into the bore of the bearing that abuts a shaft shoulder or similar fixedcomponent. The sleeve is located on the shaft by a nut or an end plate. Lock nuts or endplates are not supplied with the extraction sleeves. KM or HM lock nuts and respective locking washers are suitable but must be ordered separately. Further information will be found in the section "Lock nuts with locking washer or clip".To secure the bearing to the shaft, press the extraction sleeve into the bearing bore. To do this, particularly where larger bearings are concerned, considerable force is required to overcome the friction between the mating surfaces of the bearing and sleeve and of the sleeve and shaft. Mounting and dismounting of bearings on extraction sleeves can be facilitated considerably by using a hydraulic nut .

Basic design
ADP extraction sleeves are slotted and have an external taper of 1:12 except for those in the A(O)H 240 and A(O)H 241 series which have an external taper of 1:30 and are intended for use with wide bearings in the 40 and 41 Dimension Series.


The nuts required for dismounting the extraction sleeve are not supplied with the sleeve and must be ordered separately. Appropriate sizes are listed in the product table. Appropriate hydraulic nuts for dismounting are listed there as well.

Design for hydraulic mounting
To enable the hydraulic mounting to be used for mounting and dismounting, ADP extraction sleeves with bore diameters of 200 mm and above are produced as standard with oil supply ducts and distributor grooves. 



These AOH sleeves have two oil supply ducts at the threaded side as well as oil distributor grooves in the circumferential and axial directions, both in the outside surface and the sleeve bore. If oil is injected through these ducts and grooves, an oil fil is formed between the mating surfaces of the bearing and sleeve and between the shaft and sleeve, and the force required to mount the bearing is considerably reduced. Details of the thread for attaching the oil supply lead to the ducts as well as of appropriate hydraulic nuts can be found in the product table.

Materials
The materials using in ADP extraction sleeves are carbon steel with a tensile strength at least 430N /mm2.

Dimensions
The dimensions of ADP extraction sleeves are in accordance with ISO 2982-1:1995.

Tolerances
The bore diameter of ADP extraction sleeves is to tolerance JS9, the width to h13.

Thread
ADP extraction sleeves up to size 38 have metric threads with 6g tolerances according to ISO 965-3:1998. Larger extraction sleeves have metric trapezoidal threads with 7e tolerance according to ISO 2903:1993.If standard nuts are not used, the threads of nuts for extraction sleeves up to size 38 should correspond to tolerance 5H according to ISO 965-3:1998. The threads of nuts for larger extraction sleeves should correspond to tolerance 7H according to ISO 2903:1993.

Shaft tolerances
As extraction sleeves adapt themselves to the shaft diameter, wider diameter tolerances can be permitted than for the seating of a bearing with a cylindrical bore. However, the form tolerances must be kept within narrow limits as the accuracy of form directly affects the running accuracy of the bearing. Generally, shafts should be machined to an h9 tolerance but the cylindricity should be to IT5/2 according to ISO 1101:2004.


Category: others